Selective 6 Layer HDI Immersion Gold PCB With Blind / Buried Holes

Selective Immersion Gold 6 Layer HDI PCB With Blind Holes And Buried Holes

PCB Specifications:

1 Part NO: HDIPCB0011

2 Layer Count: 6 Layer HDI PCB

3 Finished Board Thickness: 1.2MM

4 Drilling: L1-L2 0.1MM, L2-L5 0.2MM, L5-L6 0.1MM, L1-L6 0.2MM

5 Min Lind Space&Width: 2.9/2.8mil

6 Copper Thickness: 1/H/H/H/H1

7 Application Area: Smart Watch

8 PCB Size: 136MM*101.5MM/9PCS

Our production applications:

1 Consumer electronic products: SSD, TWS earphones, headsets,computer devices, portable power supplies, bluetooth modules, gps modules, wifi modules, smart keys for cars, intelligent locks, floor mopping robots, zigbee, etc.

2 Industrial control:main boards in machines, industrial robots, servo motors etc.

3 Automotive: BMS main boards, automotive radar etc.

4 Power supplies: UPS, industrial power supply, frequency power supply.

5 Medical: medical equipment, medical equipment power supply.

6 Communication products: 5G base station, routers, satellites, antennas.

7 Photovoltaic inverter

IT180A DATA SHEET:

Q1: What is the Comparative Tracking Index (CTI) or Proof Tracking Index (PTI) of the PCB base material?

A1:

Comparative Tracking Index (CTI) is the extent to which the insulating material of the PCB can resist the unwanted current to flow between traces on the board. It is a measure of the ability of the PCB substrate to withstand any breakdown between two tracks on the PCB surface. It is used to assess the proportionate resistance of the PCB base material and helps calculate the high-voltage isolation values between the tracks. The CTI / PTI value indicates how resistant the PCB material is against environmental influences such as dirt and moisture. The higher the value, the more resistant the material is. The default CTI value for FR4 is 175 and goes up to 600 on special materials. The CTI / PTI value is determined using standard test methods.

Tracking resistance is the resistance offered by the PCB trace against the current flow. The higher the number of components placed on the PCB board the higher is its overall packing density, this leads to smaller trace spacings. Therefore, the CTI / PTI value in the PCB base material is of prime importance. These values help to deduce the overall PCB tracking resistance.

These values give an estimation for leakage or short-circuit as trace spacing becomes small due to the increased number of components. As per the IEC standard, the smaller CTI grade substrate offers good resistance to the electrical breakdown. CTI is a critical number while selecting a PCB material. Normal FR-4 ranges from 175 to 225V. IEC has prescribed three of the following classes for PCB CTI calculation:

Understanding CTI with respect to PCB routing:

When two PCB traces run in parallel, the dielectric material should not breakdown at any time and both traces should be able to carry current without any problem. The chance of dielectric breaking down and the traces having a direct short is very less. The dielectric ensures that resistance is present between the two traces. One of the primary reasons why the two traces might have leakage current is due to the impurities forming between traces, environmental conditions, voltage applied, and temperature..

CTI is the measurement of the susceptibility of the PCB’s insulating material to the electrical breakdown. Mathematically, CTI is that voltage, which results in failure by breakdown after 50 drops of 0.1 percent ammonium chloride solution have fallen on the material.

Creepage Distance and CTI Value:

Creepage distance is the shortest path available between two PCB conductors measured along the surface of the insulation. Depending upon the CTI value of the PCB base material, the creepage value will differ. If the CTI value is higher, then the minimum creepage value is required. In short, high a CTI value indicates closeness between the PCB conductors.

Witgain Technology Limited was established in 2007. Factories locate in HuiZhou City and marketing locates in ShenZhen City. The total area of two factories is around 10000 square meters. We can offer 2-layer and multi-layer pcb services to our customers, highest to 24 layers and rigid-flex pcb, ceramic pcb, HDI pcb, heavy copper pcb are also included. To meet our customer's diversified demands, we also accept prototype orders, small batch orders and big batch orders. Quality and technology is what we value most and we will never stop improving our capabilities. Our customers' satisfaction is always what we are seeking for.