New Technical Clay Brick Mixing Equipment Block Plant Mixer Double Shaft Mix Machine

New technical clay brick mixing equipment block plant mixer double shaft mix machine

TWGD model double shaft extruding mixer is a new product developed by our company on the basis of absorbing the advanced experience of similar products abroad, and it occupies a leading position among similar products in China. This machine is a raw material processing equipment, suitable for sintered brick production lines fired with clay, shale, coal gangue and sludge as the main raw materials. It is mainly used for stirring, extrusion and kneading of mixed materials and water to improve the plasticity and forming ability of raw materials. It has the characteristics of uniform stirring, strong load bearing capacity, long service life and wide application range.

Double shaft mixer technical parameters:

Double shaft mixer working principle and structural characteristics

Working principle

The power drives the two shafts of the mixer to rotate in opposite directions through the reducer and the gear pair of the gearbox. The two shafts are respectively equipped with stirring knives with opposite directions.

The stirring knife makes the material toss, shear and convection; at the same time, the water spray system sprays mist water to the material, and mixes it with it. With the rotation of the stirring shaft, the stirring blade continuously stirs, mixes and homogenizes the raw materials, and continuously pushes the raw materials to the feeding port of the sealing cylinder. After the raw material enters the sealed cylinder, its density increases continuously due to the influence of the volume compression of the compressor head. During this process, the kneading effect between the mud materials further improves the homogenization effect on raw materials of different properties. Under the action of the extrusion reamer, the mud materials are forced and continuously squeezed from the discharge port of the compressor head. There is a pair of relatively rotating mud scrapers at the discharge port, so as to cut the continuously extruded mud ring into uniform pieces and fall into the next production process.

Brick mixer structural characteristics

The main part of this series of equipment are mainly composed by transmission motor, pneumatic clutch, hard-type tooth reducer, gear box, stirring tank, stirring shaft, stirring knife, sealing cylinder, screw reamer, compressor head, trowel, base and other parts composition. There is a water adding pipeline on the stirring tank, which is used to adjust the moisture content of the raw materials. A pneumatic clutch is arranged between the motor and the reducer, which can realize the un-load start of the motor and also provide overload protection. The cutter head and trowel of the stirring blade are cast with wear-resistant alloys, and are connected with the fixed seat by high-strength bolts, which is convenient for maintenance and replacement. The extrusion reamer and the inner and outer conical sleeves are all made of wear-resistant alloy steel, which is wear-resistant and easy to replace.

Clay brick making factory double shaft mixer machinery

BBT supply red clay brick making project machinery and equipment

key equipment:
TWPM Wet pan mill
TWJH filter mixer
GD box feeder
TRA double tooth roller crusher
TWGD double shaft mixer

New technical clay brick mixing equipment block plant mixer double shaft mix machine

BBT focuses on the core business development by concentrating on the professionalization strategy. We devote ourselves to integrating technical solutions of production line process design, thermal design, equipment R&D, trade,mechanical and electrical equipment installation, international engineering, project consultancy, technical service for producing sintered wall materials of fired perforated brick, paving block, facing brick, hollow block, insulating block, wall board.

BBT takes the market demand as guidance, creates the value for the customer as objective and sincerely provides:

1. Process design of directing setting, two times setting and firing technology(BBT masters core technology);

2. Wall boards production process technology;

3. Prefabricated walls production process technology;

4. Key equipment in raw materials treatment process: wet pan mill, high speed fine-pulverized roller;

5. Key equipment in molding process: extruding type mixer and filter mixer;

6. Equipment R&D and manufacturing of fully automatic cutting, marshalling, brick stacking, loading and unloading;

7. Equipment R&D and manufacturing of thermal running, thermal monitor and control system;

8. All types of fuel combustion and control systems;

9. Management services of brick & tile production technology.

With the love of brick, BBT will continue to take unremitting efforts to provide our clients with high standard brick making production line through continuous innovation and strict industrial chain development and management.