3126 Engine Overhaul Rebuild Kit For Replacement Parts

3126 engine overhaul rebuild kit for replacement parts

product description

introduce

Introduction to 3126 engine installation
Preparation before installation
Site and tool preparation: A clean, dry and well-ventilated installation site is required to ensure that there is enough space to operate the engine and use tools. Prepare suitable lifting equipment, such as a crane or forklift, whose load capacity should be able to safely lift the 3126 engine (the weight of the engine varies depending on the configuration, generally around several hundred kilograms). At the same time, prepare various tools required for installation, such as torque wrenches, socket wrenches, screwdrivers, etc., and the tools must meet the corresponding specifiions.
Inspect the engine and accessories: Before installation, carefully inspect the appearance of the 3126 engine to check whether there is any damage caused during transportation. Check whether the various interfaces, pipe connection points and mounting holes of the engine are intact. At the same time, check the model and serial number of the engine to ensure that they are consistent with the installation requirements. Also check the supporting parts, such as the intake duct, exhaust duct, cooling system components, fuel system components, etc., to ensure that they are intact and not damaged.
Engine installation steps
Positioning and fixing: Use lifting equipment to slowly lift the engine, align it with the installation position and gently lower it. Make sure that the engine is placed stably on the mounting base and the mounting holes are accurately aligned. Then, use bolts of specified specifiions to initially fix the engine to the base, but do not tighten the bolts completely. During the fixing process, pay attention to the installation direction of the engine to ensure that its output shaft, flywheel and other components are positioned correctly and match the equipment to be connected later.
Connect the cooling system: Connect the engine's coolant inlet and outlet to the cooling system pipeline. During the connection process, use new sealing gaskets to ensure a tight connection to prevent coolant leakage. For the clips or clamps of the coolant pipeline, install them firmly and do not over-exert the pipeline. After the connection is completed, check the coolant level and add coolant if necessary.
Connect the fuel system: Connect the fuel filter, oil pump and other fuel system components to the engine's fuel interface. When connecting the fuel pipeline, pay attention to avoid pipeline distortion and ensure that the connection is well sealed to prevent fuel leakage. After the connection is completed, the fuel system needs to be vented to ensure that the fuel can be smoothly supplied to the engine.
Connect the intake and exhaust systems: Connect the intake pipe to the engine's air intake, ensure that the inside of the pipe is clean, and no debris enters the engine. The connection of the exhaust system is equally important. Ensure that the exhaust pipe is tightly connected to the engine's exhaust port, and install the muffler and exhaust treatment device (if required) to reduce noise and meet environmental standards.
Connect the electrical system: According to the engine's electrical wiring diagram, connect the lines of electrical equipment such as the starter motor, generator, and sensor. During the connection process, pay attention to the correspondence between the color coding of the line and the interface to ensure that the connection is correct. After the connection is completed, use insulating tape or wire tube to organize and protect the line to prevent the line from being exposed to damage or interference.
Debugging and inspection after installation
Check the installation: Carefully check all the connection parts of the engine, including pipe connections, electrical connections, and mechanical connections, and ensure that all bolts and nuts have been tightened to the specified torque. Check whether there are any debris or tools left around the engine, and clean up the installation site.
Initial startup and debugging: Before starting the engine, check the coolant level, fuel level, and oil level again to ensure that they are within the normal range. Then, start the engine according to the correct startup procedure. After starting, observe the operation of the engine and check for abnormal vibration, noise, or leakage. Check the various indior lights and instrument readings on the dashboard, such as the water temperature gauge, oil pressure gauge, tachometer, etc., to ensure that all parameters are normal. If any abnormality is found, stop the engine immediately to check and troubleshoot.
3126 engine power introduction
Power parameters: The power output of the 3126 engine varies depending on different configurations and appliion scenarios. Its rated power is generally between 130-230 horsepower (about 97-172 kilowatts). For example, in some medium-sized construction machinery appliions, its power output may be in a lower range to meet the power requirements of the equipment under general working conditions; in situations where higher power is required, such as some special construction machinery or generator set appliions, its power can reach a higher level.
Power characteristics and advantages: The engine can output large torque in the medium and low speed range, which enables it to respond quickly when starting and under large load changes. This feature is very beneficial for construction machinery and vehicles that need to start and stop frequently and cope with different loads. For example, during the operation of the excavator, when the digging arm digs heavy objects, the engine can quickly provide enough torque to drive the hydraulic system to ensure the smooth progress of the digging action. In vehicle appliions, this torque characteristic can make the vehicle easier when climbing or starting with full load.
Introduction to the applicable models of 3126 engine
Construction machinery
Excavator: 3126 engine is an ideal power source for many medium-sized excavators. Taking a certain medium-sized excavator of as an example, its working weight is between more than ten tons and more than twenty tons. The 3126 engine provides power for it and drives the hydraulic system so that the digging arm, bucket and other components can efficiently perform digging, loading and other operations. When digging soil or stone of different hardness, the power output of the engine can ensure digging efficiency and stability.
Loaders: In loaders, the 3126 engine can provide power for the forward and reverse movements of the loader and the lifting and lowering of the bucket. When the loader is loading and unloading bulk materials (such as sand, gravel, coal, etc.), the engine power can ensure that the bucket is quickly inserted into the material pile and the materials are lifted and unloaded powerfully, improving loading and unloading efficiency.
Bulldozers: For bulldozers, the torque output of the 3126 engine can effectively drive the bulldozer to do bulldozing on the ground. Whether on a flat site or in an area with a certain slope, the engine can provide enough power to push a large amount of soil or other materials.
Vehicles and generator sets
Medium trucks: Some medium-sized cargo trucks use the 3126 engine. When transporting goods such as construction materials and agricultural products, the engine can provide stable power to keep the vehicle in good driving performance under different road conditions (such as highways, rural roads, etc.). Its power output can meet the vehicle's acceleration, climbing and cruising needs, and it also has certain advantages in fuel economy.
Generator Sets: The 3126 engine can be used for small and medium-sized generator sets. It can output electricity stably at construction sites, field sites or as an emergency backup power source. Depending on the configuration, the output power of the generator can meet the power demand within a certain range, such as providing power for some small construction equipment, lighting equipment, etc.
Introduction to Applicable Models of 3126 Engines
Own Equipment Models: In brand equipment, such as some models of 320 series excavators, 966M series loaders, etc., the 3126 engine is an adapted power unit. The overall design of these equipment, including the spatial layout of the power compartment, the matching of the transmission system, the integration of the cooling system and the electrical system, are closely matched with the 3126 engine, which can give full play to the performance of the engine.
Other compatible equipment models: In addition to 's own brand equipment, some other brands of medium-sized construction machinery and vehicles can also be installed with the 3126 engine if their power system design allows. For example, some modified domestic or imported medium-sized excavators, loaders and other equipment can be adapted to the 3126 engine through appropriate modifiion and adjustment, such as replacing the engine bracket, adjusting the transmission system and cooling system, etc., to improve the power performance of the equipment.
DAILY REFINING brand is suitable for engine parts
Brand part adaptability: The parts provided by the DAILY REFINING brand are specially designed for engine repair and maintenance, and many of them are suitable for the 3126 engine. These parts are carefully designed in size, specifiions and performance, and can work well with other parts of the 3126 engine to ensure the normal operation of the engine.
Examples of part types and functions: For example, the cylinder liner is the inner liner of the engine cylinder and is in direct contact with the piston and piston ring. The cylinder liner of the DAILY REFINING brand is made of high-quality materials with good wear resistance and corrosion resistance. It can withstand the high temperature and high pressure generated by the reciproing motion of the piston and combustion, effectively protecting the engine cylinder and extending the service life of the engine. Pistons and piston rings are also important parts. The piston moves up and down in the cylinder, converting the pressure generated by combustion into power, while the piston ring plays the role of sealing the cylinder to prevent combustion gas leakage and oil from entering the combustion chamber. The brand's pistons and piston rings are of high quality and can ensure the power output and fuel economy of the engine.
Introduction to diesel engine parts operated by the company
Overview of parts types and functions
Cylinder liner, piston, piston ring: The cylinder liner provides guidance and support for the movement of the piston, and cooperates with the piston ring to seal the high-temperature and high-pressure gas in the combustion chamber. The piston is a key component that converts the heat energy generated by fuel combustion into mechanical energy, and it moves up and down in the cylinder liner. The piston ring ensures the sealing between the piston and the cylinder liner and controls the consumption of engine oil.
Valve, seat ring, guide: The valve controls the intake and exhaust process of the engine. The seat ring ensures that the valve can fit tightly when closed to prevent gas leakage. The guide ensures that the valve can move accurately during the opening and closing process, maintaining normal intake and exhaust timing and flow, thereby affecting the combustion efficiency and power output of the engine.
Main bearing, connecting rod bearing, thrust: bearings are mainly used to support the rotational movement of the crankshaft and connecting rod, reducing friction and wear. Thrust bearings bear the axial force generated when the engine is running, ensuring the axial positioning of the crankshaft and connecting rod, so that the engine can run stably.
Oil pump, water pump, cylinder block, cylinder head, crankshaft, connecting rod, camshaft: the oil pump is responsible for delivering oil to various parts of the engine that need lubriion to reduce friction between parts. The water pump circulates coolant to ensure that the engine works within a suitable temperature range. The cylinder block is the main structure of the engine, accommodating components such as pistons and crankshafts. The cylinder head seals the top of the cylinder and is equipped with valves, fuel injectors and other components. The crankshaft converts the reciproing motion of the piston into rotational motion and outputs power. The connecting rod connects the piston and the crankshaft to transmit power. The camshaft controls the opening and closing time and lift of the valve, and plays a key control role in the intake and exhaust process of the engine.
Parts quality and advantages: These engine parts operated by the company have undergone strict quality inspections. In terms of material selection, high-quality metal materials and composite materials are used to ensure the strength, hardness, wear resistance and corrosion resistance of parts. In terms of manufacturing technology, advanced processing technology is used to ensure the accuracy and dimensional tolerance of parts, so that each part can better cooperate with each other and improve the overall performance and reliability of the engine.
Future development of Guangzhou Tengsong Engineering Testing Equipment Co., Ltd.
Direction of technological innovation: With the continuous development of the engineering equipment industry, the accuracy and efficiency of engine parts detection are increasingly required. The company can increase its investment in the research and development of detection technology and introduce advanced non-destructive testing technologies such as ultrasonic testing, magnetic particle testing, and radiographic testing to detect internal defects and surface cracks in engine parts. At the same time, develop intelligent testing equipment that can automatically identify problems such as dimensional deviations and material performance differences of parts through sensors and data analysis systems to improve the accuracy and reliability of detection.
Market expansion strategy: The company can further expand its market scope, not only to consolidate its market share in existing customer groups such as construction machinery, repair shops, and retail stores, but also to actively explore new customer areas. For example, establish cooperative relationships with automobile manufacturers, shipbuilding companies, etc., and promote the company's engine parts and testing equipment to these fields. In addition, we will use the Internet platform to carry out online sales and technical consulting services to improve the visibility and market coverage of the company's products.
Service quality improvement: Focus on improving the quality of after-sales service and establish a complete customer feedback mechanism. For problems encountered by customers in the process of using the product, we can provide timely technical support and solutions. We can provide product training services to help technicians and mechanics in repair shops better understand and use the company's engine parts and extend the service life of the products. At the same time, we will strengthen cooperation with suppliers to ensure the supply stability and quality reliability of parts and provide customers with better services.
Introduction to high-quality product parts
Quality standards and characteristics: High-quality engine parts have strict standards in terms of materials, processing technology and performance. For example, in terms of materials, high-purity metal materials are used, and special heat treatment processes are used to give the parts good mechanical properties. For example, the crankshaft is forged with high-quality alloy steel. After quenching and tempering, its surface hardness can reach HRC50-60, the core hardness is moderate, it has good toughness, and can withstand huge torsion and bending stresses. In terms of processing technology, high-precision processing equipment is used, and the dimensional accuracy of the parts can be controlled at the micron level. For example, the diameter tolerance of the piston can be controlled between ±0.01 - 0.03mm, and the cylindricality and roundness tolerances are also within a very small range, ensuring precise matching with the cylinder liner.
Improvement of engine performance: These high-quality parts can significantly improve engine performance. Taking the valve as an example, high-precision valves can accurately control the time and flow of intake and exhaust, making the fuel and air mix more fully, improving combustion efficiency, thereby increasing the engine's power output and reducing fuel consumption. High-quality pistons and piston rings can reduce the internal friction loss of the engine, improve power transmission efficiency, and effectively prevent oil from entering the combustion chamber, reduce the blue smoke phenomenon in exhaust emissions, and extend the service life of the engine.
Rebuilding overhaul kit price introduction
Price range and factor analysis: The price of rebuilding overhaul kits ranges from $90 - $130 - $180 - $300 - $900 - $1500. The price difference mainly depends on the type, quantity and quality of parts included in the kit. Lower-priced kits may mainly contain some small seals, gaskets or simple consumable parts, which are suitable for simple repairs or maintenance of the engine. Higher-priced kits, such as kits of $900-$1500, usually contain key large parts such as cylinder liners, pistons, crankshafts, etc., which can meet the needs of comprehensive reconstruction or overhaul of the engine. These parts are more expensive and the manufacturing process is more complied.
Price advantage and market competitiveness: The company's multi-price range of rebuilding and overhaul kits can meet the needs and budgets of different customers. For some small repair shops or price-sensitive customers, they can choose lower-priced kits to replace some parts, solve some minor engine faults or perform routine maintenance. For customers who need a comprehensive overhaul of the engine, the high-quality and relatively high-priced kits provided by the company can ensure the quality of the overhaul and restore the performance of the engine. This flexible pricing strategy helps to improve the company's competitiveness in the market.,

attracting more customers at different levels.
Product scope of appliion
Construction machinery field: In the field of construction machinery, the company's products are suitable for various types of equipment. For example, in tower cranes, the quality of engine parts directly affects the lifting capacity and working efficiency of the crane. High-quality oil pumps and water pumps can ensure the lubriion and cooling of the engine, so that the crane can maintain stable power output during long-term work and safely lift heavy objects. In concrete mixer trucks, the reliability of the engine is crucial. The parts operated by the company can be used to repair and maintain the engine of the mixer truck, ensuring that the mixer truck can operate normally during the transportation of concrete, and avoiding problems such as concrete solidifiion in the tank due to engine failure.
Repair shop and retail store field: Repair shops can use the engine parts provided by the company to provide repair services for equipment of various brands. Whether it is a , Cummins or other brand engine failure, the repair shop can purchase the right parts from the company for repair. Retail stores can sell these products as inventory to end users, such as mechanics and owners of construction machinery. The detailed product alog and technical support provided by the company can help repair shops and retail stores better select and sell products.
Mechanic field: Mechanics are the people who directly use these products to repair and maintain engines. The high-quality parts and rebuild overhaul kits provided by the company can provide convenience for mechanics. They can choose the appropriate parts for repair according to the actual fault conditions of the engine. At the same time, the products provided by the company are reliable in quality and highly adaptable, which can help mechanics improve the efficiency and quality of repairs, reduce the number of reworks during the repair process, and improve customer satisfaction.

Company Profile

 广州腾松工程机械设备有限公司，专业柴油发动机配件，18年行业经验，专注于工程机械、农业、发电机组、船舶、挖掘机、装载机、推土机、平地机、起重机、卡车、叉车等DAILY REFINING品牌机械发动机配件。我们与欧洲、美洲、中东和东南亚地区合作，并在50多个国家建立了业务关系。

DAILY REFINING品牌：品质与创新的发动机零部件品牌

DAILY REFINING 是一个致力于提供高品质创新型发动机零部件的品牌。通过持续的研发和严格的质量控制，DAILY REFINING 为全球汽车和机械行业提供高品质的发动机零部件解决方案。本文将介绍 DAILY REFINING 品牌在发动机零部件领域的核心价值、技术实力及其卓越地位。

DAILY REFINING 的品牌核心价值体现于其对品质和可靠性的承诺。他们注重产品性能、耐用性和安全性，并致力于为客户提供卓越的发动机零部件。品牌价值观包括卓越的品质、领先的创新能力和客户满意度，这些价值观贯穿于 DAILY REFINING 的产品和服务之中。

日精拥有专业的研发团队和先进的生产设备，奠定了坚实的技术实力基础。他们持续投入研发，并与行业领先的合作伙伴携手，不断推动发动机零部件技术的创新。日精的发动机零部件经过严格的测试和质量控制，确保其在各种工况下的可靠性和卓越性能。

DAILY REFINING 的发动机零部件产品线广泛覆盖船舶、工业机械等多个应用领域。我们提供活塞、曲轴、缸套、缸盖等各种类型的零部件，以满足不同发动机的需求。无论是传统的燃油发动机还是先进的电动汽车发动机，DAILY REFINING 都致力于提供高质量、高性能的发动机零部件。

DAILY REFINING对产品质量有着严格的把控和保障。他们采用先进的生产工艺和质量管理体系，确保每一个发动机部件都符合高标准。DAILY REFINING的零部件经过长期的实验和验证，即使在严苛的工作环境下也能保持稳定可靠的性能。

作为一家专注于品质与创新的发动机零部件品牌，DAILY REFINING凭借卓越的技术实力和不懈的努力，在业界树立了良好的口碑。他们提供多样化的发动机零部件解决方案，为全球汽车和机械行业的发展做出了重要贡献。未来，我们期待DAILY REFINING继续引领发动机零部件领域的创新，为客户提供更可靠、更高性能的发动机零部件，推动整个行业的发展。