Product Details
Company Profile

S5731S-H24T4XC-A Huawei Network Switch 24 10/100/1000BASE-T Ethernet Ports

S5731S-H24T4XC-A (02352YRG/02352YRG-001/02352YRG-003)

Version Mapping

Table 4-1444 lists the mapping between the S5731S-H24T4XC-A chassis and software versions.

Table 4-1444 Version mapping

Series

Model

Software Version

S5731S-H

S5731S-H24T4XC-A

02352YRG: V200R019C00 and later versions

02352YRG-001: V200R020C10 and later versions

02352YRG-003: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch. If V200R021C00SPC100 is used, install V200R021SPH013 or a later patch.)

Appearance and Structure

Figure 4-561 S5731S-H24T4XC-A (02352YRG) appearance

Figure 4-562 S5731S-H24T4XC-A (02352YRG-001/02352YRG-003) appearance

1	Twenty-four 10/100/1000BASE-T ports	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (100M/1000M auto-sensing) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking)
3	One console port	4	One ETH management port
5	One USB port	6	One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.
7	Ground screw NOTE: It is used with a ground cable.	8	Rear card slot NOTE: Applicable card: ES5D21X08T00 ES5D21Q02Q00 S7X08000 (02312URW) (applicable in V200R019C10 and later versions) S7X08000 (02312URW-002) (applicable in V200R021C10SPC600 and later versions) S7Q02001 (02313UBW) (applicable in V200R021C01 and later versions) S7Q02001 (02313UBW-002) (applicable in V200R021C10SPC600 and later versions)
9	Fan module slot 1 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))	10	Fan module slot 2 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))
11	Power module slot 1 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module) PAC150S12-R (150 W AC Power Module) PDC180S12-CR (180 W DC Power Module) (applicable in V200R020C00 and later versions)	12	Power module slot 2 NOTE: Applicable power module: PAC600S12-CB (600 W AC&240 V DC Power Module) PAC600S12-EB (600 W AC&240 V DC Power Module) PAC600S12-DB (600 W AC&240 V DC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module) PAC150S12-R (150 W AC Power Module) PDC180S12-CR (180 W DC Power Module) (applicable in V200R020C00 and later versions)

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-1445 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

Table 4-1445 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

10GE SFP+ optical port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1446 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-1446 Attributes of a 10GE SFP+ port

Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1447.

Table 4-1447 Attributes of a console port

Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1448 describes the attributes of an ETH management port.

Table 4-1448 Attributes of an ETH management port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working Mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5731S-H24T4XC-A has similar indicators to those on the S5731-H48P4XC except that the S5731S-H24T4XC-A does not have a PoE mode indicator. For details, see Indicator Description.

Power Supply Configuration

The switch can use a single power module or double power modules for 1+1 power redundancy. Pluggable AC and DC power modules can be used together in the same switch. However, the power modules with natural heat dissipation and the power modules with fan cannot be used at the same time.

Heat Dissipation

The S5731S-H24T4XC-A uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-1449 lists technical specifications of the S5731S-H24T4XC-A.

Table 4-1449 Technical specifications

Item	Description
Memory (RAM)	4 GB
Flash	1 GB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	57.73 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	Common mode: ±6 kV
Power supply surge protection	Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.4 in. x 17.7 in.)
Weight (with packaging)	9.35 kg (20.61 lb)
Stack ports	10GE SFP+ ports on the front panel, or ports on the rear card
RTC	Supported
RPS	Not supported
PoE	Not supported
Rated voltage range	AC input: 100 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC DC input: -48 V DC to -60 V DC
Maximum voltage range	AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC DC input: -38.4 V DC to -72 V DC
Maximum power consumption (100% throughput, full speed of fans)	114 W (without card)
Typical power consumption (30% of traffic load, tested according to ATIS standard)	88 W (without card)
Operating temperature	-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0°C (32°F).
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 57.5 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02352YRG 02352YRG-001 02352YRG-003

Notices:

1. Open the packaging, check the products carefully, and take them gently.
2. The product is a brand new original unopened equipment.
3. All products 3 year warranty, and the buyer is responsible for the return shipping cost.

International Buyers Please Note:
Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Customs fees are normally charged by the shipping company or collected when you pick the item up. These fees are not additional shipping charges.
We won't under-value merchandise or mark the item as a gift on customs forms. Doing that is against U.S. and international laws.
Customs delays are not the responsibility of the seller.
Inspur NF5270M6/NF5280M5/ NF2180M3/NP5570M5/NF3120M5/NF8480M5
Dell P5820/T7920/R250/R450/R540/R650/R650xs/R740/R750/R750xs
xfusion 2288HV5 2488HV5 5588HV5

Need to contact:
WeChat: +8613651169867
Skype: +8613651169867
WhatsApp: +8615732685076

Product Tags:


*From:	Your email address is incorrect!
*To:	Beijing Qianxing Jietong Technology Co., Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	Datacom Switches
Brand Name:	HUA WEI
Model Number:	Huawei switch S5731S-H24T4XC-A
MOQ:	1
Price:	$705.7362~1143.2927 Negotiable
Payment Terms:	T/T
Supply Ability:	100
product name:	network communication switch
Brand model number:	Huawei switch S5731S-H24T4XC-A
Number of ports:	24 Gigabit Ethernet ports
port type:	24Gigabit Ethernet ports 4 10 Gigabit SFP+

S5731S-H24T4XC-A Huawei Network Switch 24 10/100/1000BASE-T Ethernet Ports

S5731S-H24T4XC-A Huawei Network Switch 24 10/100/1000BASE-T Ethernet Ports

S5731S-H24T4XC-A Huawei Network Switch 24 10/100/1000BASE-T Ethernet Ports

S5731S-H24T4XC-A (02352YRG/02352YRG-001/02352YRG-003)

Version Mapping

Appearance and Structure

Port Description

Indicator Description

Power Supply Configuration

Heat Dissipation

Technical Specifications

S5731S-H24T4XC-A Huawei Network Switch

24 Ethernet Ports Huawei Network Switch

S5731S-H24T4XC-A Huawei Network Switch 24 10/100/1000BASE-T Ethernet Ports