BARRED TEE ASTM A815 UNS S31803 DN200 SCH40S

BARRED TEE ASTM A815 WP- UNS S31803 DN200 SCH40S

The ends of all buttweld fittings are bevelled, exceeding wall thickness 4 mm for austenitic stainless steel, or 5 mm for ferritic stainless steel. The shape of the bevel depending upon the actual wall thickness. This bevelled ends are needed to be able to make a "Butt weld".

Welding Bevel acc.to ASME / ANSI B16.9 and ASME / ANSI B16.28

Design considerations for barred tee

The barred tee will be used when there is a requirement for pigging. Thus, many of its applications can be found in the pipeline or in the subsea field.

The bar plates that welded internally at the branch are to avoid the pig from changing direction or getting stuck at the branch outlet.

The design of the bar plates must be in sufficient quantity, thickness and adequately spaced to ensure the smoothness for the pig to run through the main pipe, and at the same time not affecting the flow that was meant to flow through the branch. Normal practice is to ensure that the opening in the branch pipeline after guided bars is not more than 40% of the main pipeline area.

The size of the bars in the branch connection has to be small enough not to restrict the flow but large enough to sustain the pressure of the flow.

To ensure the smoothness, the bar plates have to be a grind to suit the branch curvature. Any sharp edges, spatters and burs are required to be removed. This smoothness of the pigging process is important to protect the sensor of the pig from damage.

Refer to Shell DEP 31.40.10.13-Gen Figure 4 above; the quantity of the bar plates start with two (2) pieces and increase as the ID of the branch increase.

The bar plates ideally will be equally spaced.

For larger tee (size 14 inches and above), there will be a bridge plate in the middle to support the bar stiffness when getting hit by the pig.

The material of the bar plates commonly used the same as the tee material for weldability.

Standard practice is to avoid welding of guide bars directly on the high-stress concentrated areas of the extrusion neck. Bar ends must be machined to fit the branch.

Weld Repairs on Parent metal is prohibited.

BRAIDED TEES MATERIAL & GRADES :

Stainless Steel Barred Tees :

ASTM A403 WP 304/ 304L/ 304H/ 316/ 316L/ 317/ 317L/ 321/ 310/ 347/ 904L

Carbon Steel Barred Tees :

ASTM A234 WPB / A420 WPL3/ A420 WPL6/ MSS-SP-75 WPHY 42/46/52/56/60/65/70

Alloy Steel Barred Tees :

ASTM A234 WP1/ WP5/ WP9/ WP11/ WP22/ WP91

Nickel Alloy Barred Tees :

ASTM / ASME SB 336 UNS 2200 (Nickel 200), UNS 2201 (Nickel 201), UNS 4400 (Monel 400), UNS 8020 (Alloy 20 / 20 CB 3, UNS 8825 Inconel (825), UNS 6600 (Inconel 600), UNS 6601 ( Inconel 601), UNS 6625 (Inconel 625), UNS 10276 (Hastelloy C 276)

Duplex & Super Duplex Steel Barred Tees :

ASTM A815, ASME SA815 UNS NO S31803, S32205. Werkstoff No. 1.4462

     TOBO GROUP sales head offce in Shanghai. 

     We are one of the Professional manufacturers Exporter  Pipeline products  in China .Our company was established in 1998, the plant covers 550, 000 square meters and a construction area of 6,8,000square meters, existing 260 workers and 45 technicians. 

      We have five branch factories which can supply the best quality pipes, tubes, fittings flanges and related accessories. Now, it owns a number of advanced pipe production equipments, metal, forging, machining, cold forming, hot extrusion, such as heat treatment process, producing 60, 000 tons of pipe fittings. Company with a variety of detection devices, such as nondestructive testing, chemical analysis, metallographic examination, physical experiments. The technical is very strength, our main products contain fittingsforged socket welding fittings and threaded fittings, pipe weld and the materials of the products contain stainless steel ,duplex-stainless steel alloy steel.

       In addition, we are authorized by more than 120 top-class mills from South Korea,Japan and China like JFE,SUMITOMO,POSCO,BAOSTEEL, TISCO,LISCO,.TPCO,HENGYANG VALIN and so on .

Our main products as follows:

• Stainless steel pipe & tube

(seamless pipe / welded pipe / square pipe /  rectangular tube,duplex stainless / inconel tube)

• Carbon / alloy steel pipe & tube

(seamless pipe / ERW / SSAW / LSAW / UOE / hollow section pipe / Galvanized Pipe)

• Tubing and casting

(line pipe,water pipeline,gas pipeline,oil pipeline)

• Special steel tube

(copper tube/titanium tube/aluminium tube/nickel alloy )

• steel bar 

(round bar/angle steel /flat steel/channel steel/steel wire)

• Pipe Fittings

(eblows, equal / reducing tees, concentric/eccentric reducers, caps, crosses, bends, dish end/end cup, stub ends, unions, couplings / hex couplings, swage nipples , nipples, hex. plug, sockolet, weldolet, thredolet, etc)

• Flange

(DIN flange/ AISI flange/blind flange/welding flange/stainless flange/slip on flange)

• steel sheet / coil

(stainless steel/carbon steel/alloy steel/galvanized steel/aluminium )

• Valve

(ball valve/gate valve/butterfly valve/globe valve/swing check valve/ check valve) 

      In order to comply with the global modernization services development trends and eliminating the varieties distress of the global enterprise‘s purchase in the consumables.. We coordinate the pressure pipe manufacturer which with the scale of production,quality control and high cost performance (has passed ISO 9001 quality series attestation, ccs, DNV,PED/97/23/EC,AD2000-WO,special equipment manufacturing license,ASME-SA182.through a variety of effective assort mechanism to make up the shortage of supply and Post-processing of VAT enterprise, and to supply high quality pipe fittings, because of the superior quality and good service, we have established long term business cooperation with more than 60 countries and areas,which covers Europe, Africa, South America, North America, Middle East, Taiwan and South East Asia and so on.

      With many years effort and support from our valuable customers, these products have obtained a big market share in the world. 

      Our business principle is "Superior quality, Competitive price, Timely delivery and Considerate service " Standing to the principle of “Enterprises focus on the core business”, TOBO will actively promotes the globalization of business strategy approach, using advanced supply chain management technology to service for clients with higher quality and more competitiveness ‘ s products. At the same time, we sincerely reply your inquiry, honesty waiting for your visiting and wish to have cooperation with you at the any time. We welcome all the customers to contact us for more information. We assure you, with our technical knowledge and experience, our company will be one of your Stable, Continuate business parters in China.

 info@tobo-group.com