Ductile Iron 500X Pressure Relief Valve Flange End Water Conservancy Valve

Introduction

500X Pressure Relief and holding valve. Used for water supply, air conditioning and fire fighting pipeline system. Medium: water, temperature ≤ 80 ℃. It is used to stabilize the pipeline pressure in front of the valve. When the pressure in front of the valve exceeds the pressure, the main valve is opened for drainage. When the pipeline pressure drops below the set value, the main valve is closed. The pressure value can be set by the pilot valve adjusting screw

Usage

The pressure releasing/sustaining valve can effectively relase the pressure that exceeds the safety set point of pilot of pilot valve in the pipeline to preventhe pipeline and equipments from damage. This valve is mainly used for the pressure escaping of the circulating system of fire control testing in the high buildingsto avoid the system trouble because of highest hydraulic pressure, alkeep the water supply pressure of the main valve always above one set value so as toensure the pressure of above main valve water supply area

working principle

First, set the opening pressure of the main valve. Loosen the pilot valve locknut, turn the pilot valve screw clockwise, and the screw moves downward. The regulating spring is compressed to apply a certain thrust to the pilot valve core. At this time, the opening pressure of the main valve increases. Turn the pilot valve adjusting screw counterclockwise, the spring pressure is released, the thrust acting on the pilot valve core is reduced, and the opening pressure of the main valve is reduced. The pressure value of the pipeline in front of the main valve can be observed through the pressure gauge. After setting, tighten the jam nut

When the pressure in front of the valve increases, the pressure in the lower chamber of the pilot valve diaphragm also increases. After exceeding the set value, the diaphragm drives the pilot valve core upward, the pilot valve opens, and the water in the upper chamber of the main valve diaphragm is discharged. When the pressure drops, the main valve core opens under the pressure difference between the upper and lower chambers of the diaphragm, the main valve begins to drain, and the pipeline pressure begins to drop

The pressure under the pilot valve diaphragm also decreases, when the pressure decreases below the set value. Under the action of the adjusting spring. The pilot valve core is closed. The pressure in the upper chamber of the main valve diaphragm increases gradually. Because the area of the main valve diaphragm is larger than the area of the main valve core, under the action of the pressure difference between the upper and lower chambers of the diaphragm. The main spool is closed. The main valve stops draining.

Summary:

1, When setting the opening pressure, gradually increase the pressure in front of the valve. Turn it on at the set value. And record the value of the pressure gauge, and then continue to increase the inlet pressure. Keep the main valve fully open (i.e. the discharge flow of the main valve will not increase). Record the discharge pressure of the main valve. Then gradually reduce the inlet pressure until the main valve is closed, and record the reseating pressure of the valve.

2, Repeat the adjustment for more than two times until the opening pressure of the main valve and the discharge pressure. Until the reseating pressure is stable.

3, When manual pressure relief is required. The pressure relief ball valve on the main valve cover can be opened, and the pressure in the upper chamber of the main valve diaphragm decreases. The main valve is then opened for pressure relief, and the outlet of the pressure relief ball valve should be connected to the drainage ditch.

4, When the opening pressure difference of main valve is p ＜ 0.5MPa, the deviation value is ± 0.02MPa. When p ≥ 0.5MPa, the deviation value is ± 0.04MPa.

5, Discharge pressure ≤ 1.08p (P is the opening pressure value

Dimension

Yuanda Valve Group Co., Ltd., founded in 1994, is headquartered in Yincun, Longyao, Hebei, China, the hinterland of Bohai Economic Rim surrounding Beijing and Tianjin. With a registered capital of RMB 200 million, Yuanda currently has 8 subsidiaries, of which 6 are in China and 2 overseas. Among them, the core company, which covers an area of 540,000m2 and has more than 3500 employees, is the largest high,midium and low-pressure valve manufacturing base specializing in valve development, manufacturing, and sales in China.

Yuanda has obtained DNV·GL, ISO9001: 2015、ISO14001:2015、OHSAS18001:2007, API6D（6D-0759）, CE, KS, and EAC certifications. Its""trademark is evaluated as Famous Trademark of China and Famous Brand in Hebei Province, and the product series produced under"" is a trademark registered in Korea and products produced under this trademark enjoy a good reputation in both international and domestic markets. Yuanda has been named “Credit Management AA-Rating Enterprise” by the General Administration of Quality Supervision, Inspection and Quarantine and granted the title of “China Quality Trustworthy Enterprise” by China Entry and Exit Inspection and Quarantine Association. It is also a holder of Manufacture License of Special Equipment Level A and Casting Certificates Grades B, B1, and B2, and a member of China Valve Association council, a corporate member of China Foundry Association, and a provincial enterprise technology center in Hebei. Yuanda has been granted the power to carry out import and export operations on its own and is an approved supplier of PetroChina (CNPC) and Sinopec, Guodian, Huaneng, Huadian, Datang and China Power, and China Aluminum, CCESCC, Shougang, Wuhan Iron and Steel Company, and Hebei Iron and Steel Company.

Yuanda manufactures to standards including GB/JB(china), ANSI, API, AWWA, DIN, BS, JIS, EAC, NF and so on, and uses HT200, HT250, QT400, QT450, WCA, WCB, WCC, CF3, CF8, CF3M, CF8M, 1Cr5Mo, LCB, among others, to produce a great variety of valves including gate valves, globe valves, ball valves, butterfly valves, check valves, diaphragm valves, pressure-relief valves, plug valves, and traps, which are available in 12 main categories, 200 series and 4000 specs, totaling 120,000 tons a year. These products are widely used in all civil sectors covering petroleum, petrochemical, chemical, power generation, metallurgy, water system, pharmaceuticals, urban construction, and water supply and drainage.