Multi - Cavity Injection Mold Plastic Fan Gate 200 x 200 KO Pattern
1. Mold life: 1000k shots or according to customers quantity
condition to decide it with saving cost for our customers.
2. The part name: Telecontroller(plastic injection mold)
3. Standard of mold accessories: LKM, DME, HASCO, MISUMI,
Meusburger, CUMSA, Progressive, INCORE, HRS, Husky, YUDO, PETS,
MOLD-MASTER, MERKLE, Parker, HPS, LKM, EUCHNER, RJG, cilpres,
NITTO, CRACK, ASSAB, GSW DIN standard, BOHLER, AISI standard, DAIDO
JIS standard, PUNCH etc according to our customers requires.
4. Plastic material: ABS+PC
5. Gate type: Sub-gate, direct gate, fan gate, point gate, edge
gate, valve gate, tip gate etc according to our customers requires.
6. Cavity material: H13 HRC48-52
7. Mold base standard: LKM Local standard, DME or HASCO, Customize
according to customers' requirements.
Mold construction description: cold runner system with sub gate, 2
plates, many lifters, inserts and shut off area.
The part name: Telecontroller
Mold type: Plastic Injection Mould with cold runner system
KO Pattern: 200*200
Sprue Radius: SR 19
Ejection type: ejection pins
Part Material: ABS+PC
Locating ring Dimension: Ф100
This part has very high appearance and size requirements, the
defect showed below will not be acceptable, for example, weld line,
Dark Sport, Sliver Marks, Gas Trap Effect, Visible Ejector
Marks,Deformation,Short shot Filling, Burnt Streaks, Sink
Marks,Flash,Over dimension, Under dimension, Stress Crack etc.
Moreover, the product finishing surface must meet the requires of
This mould is made in Shiny Mould Factory. It is a mould exported
to Europe, with complicated structures and high quality requests.
Customer needs mold life to be over 1 million shots. We can ensure
this mold life and give warrant to our customer that once some
mould components are broken during working, if it is caused not by
the operation fault from the workers, we can provide new mould
components to them free of charge.
Molding the plastic product by plastic injection machine
Telecontroller(plastic injection mold)
3.mould base material
H13 HRC48-52,S136,420, P20, D2, 1040, 0-1, S-7, A2, 1.2344, 1.2083,
1.2311, 1.2739, 1.2343, 1.2510, 1.2767,NAK80,SKD61,718,738,DF-2 etc
1000k shots or according to customers quantity condition to decide
it with saving cost for our customers.
Sub-gate, direct gate, fan gate, point gate, edge gate, valve gate,
tip gate etc according to our customers requires.
10. mould base standard
LKM Local standard, DME,HASCO,Customize according to customers'
12. standard of mold accessories
LKM, DME, HASCO, MISUMI, Meusburger, CUMSA, Progressive, INCORE,
HRS, Husky, YUDO, PETS, MOLD-MASTER, MERKLE, Parker, HPS, LKM,
EUCHNER, RJG, cilpres, NITTO, CRACK, ASSAB, GSW DIN standard,
BOHLER, AISI standard, DAIDO JIS standard, PUNCH etc according to
our customers requires.
Auto CAD ,UG, Pro-E ,Solid Works,Moldflow,etc.
14. File Formats
Auto CAD (DWG), DXF, JPG or JEPG, PDF, Pro-E or
Pro/Engineer(DRW,PRT), IGES, STEP,XTL,UG parts etc.
15. injection molding machine
T/T, To be negotiated
Wooden case or Wooden box with steel frame
19. delivery time(day)
30 T1 according to customers' requirements
20. OEM or ODM
21. mould logo
Based on customer requires
22. after-sales service
one year is warranties
SHINY MOLD management introduction
In order to ensure mold quality, complete customer mold in time and
make processing technic and mold structure more reasonable in mold
design and manufacture, The company added various review in various
stages of mold design and manufacturing, at the same time, we also
check everybody on work schedule, work quality, workload, etc,
which will greatly mobilize the enthusiasm of the staff work.
1. Making mold progress schedule and evaluation based on standard
2. Making everybody workload based on standard man-hour quota.
3. Work quality evaluation, design and manufacture of abnormal
reward and punishment based on our QC record.
Review on the mold structure and processing technic:
1. Mold preliminary review: According to customer requirements to
making the mold specification table, and determining the mold
parting line, the slider or lifter structure, mold insert type,
ejector type, cooling water method and plastic product issue by the
design director, project director and deputy general manager. The
design engineer makes the DFM report according to the mold
preliminary report, drawing 2D mold structure drawing or 3D
2. Review before cutting steel: When the custom confirms the mold
trial date, project engineer must arrange the mold Kick off meeting
immediately. After that, on the same date, design engineer must
complete the drawings needed to modify and book bulk raw materials
such as mold base and cavity insert. The meeting mainly review mold
runner system, the parting line, ejection mechanism, cooling water
system, mold component strength and whether to meet customer
requirements and standards etc.
3.processing technic review: mainly review manufacturing processing
and assembling processing, the 3D mold drawing details, see whether
mold parts processing is too difficult, whether can ensure the
quality requirements, if manufacturing processing and assembling
processing is economical , if mold clearance, part number and
standard is in accordance with the requirements of the company to
1-SHINY Mold is a professional Telecontroller injection mold maker
and supplier in China. We have accumulated much experience in this
field. We have cooperated with many companies domestic and
overseas. And we have gained much good reputation from our clients.
2- SHINY can make mold according to the standard showed below, for
example, LKM, DME, HASCO, MISUMI, Meusburger, CUMSA, Progressive,
ETC, we have many world class supplier to meet our mold requires,
for example, INCORE, HRS, Husky, YUDO, PETS, MOLD-MASTER, MERKLE,
Parker, HPS, AHP Merkle, LKM, EUCHNER, RJG, cilpres, NITTO, CRACK,
ASSAB, GSW DIN standard, BOHLER, AISI, DAIDO JIS standard, PUNCH
etc. We can complete reach the customer’s requirement because of
the excellent skills, experienced design capability and software,(
for example Auto CAD,UG, Pro/E ,Solid Works, Mold flow etc)complete
procession equipment, strict quality control system.
3- SHINY has widely served in the field of plastic injection mold,
die casting mold, precision plastic mold, double-color mold with
more than 10-years experience for auto parts, home appliance,
electronic, pipe connector, gear, fitness equipment, medical
treatments. Aluminum alloy, zinc alloy and magnesium alloy products
4- Software and Hardware well equipped. For example, high speed CNC
with 2µm high-precision, CMM with 1µm high-precision, slow Wire Cut
Machine with SODICK, Mirror EDM with SODICK, Milling and Precision
Grinder machine with 2µm high-precision, at the same time, we also
install these software like Auto CAD,UG, Pro/E ,Solid Works, Mold
5- We offer advanced R$D service and best engineer to our
customers, DFM and Mold Flow Analysis.
6- High quality, competitive price, on time delivery and excellent
7- Patient communication, during the design, we know customer’s all
side requests trough deeper communication.
8- Series service of design, prototyping, painting, silk-printing
and assembly (2 assembly lines for finished products)
9- SHINY offers pipe fitting mold including: PVC Pipe fitting
mould, PE Pipe fitting mold, PP Pipe fitting mould, PPR Pipe
fitting mold, ABS Pipe fitting mould etc.
SHINY not only provides thread mold and pipe fitting mold for
injection mold company and injection mold manufacturers who want to
buy plastic mould from China with competitive price, on time
deliver and professional service.
10-SHINY uphold the quality first, the user-oriented management
philosophy and dedication to customer service, SHINY MOLD
management introduction is showed below.