Company Control Pneumatic Switch Heavy Rail System Remote Control
Monorail crane dedicated switch is a locomotive from roadway into
another roadway line connecting device, can put a rail branch for
two, give full play to the line through the ability. Through the
cylinder (pneumatic) or pull (manual) realize reversing. To prevent
vehicles from empty rail slide, each branch is equipped with
stopper. According to the different ways of operation can be
divided into manual, pneumatic and drive three. Manual switch
structure simple, suitable for underground without air, Pneumatic
switch is in the manual switch basis, the cylinder provides the
power to realize reversing; Common switch is based on the pneumatic
switch installed remote control and testing of the protection
system of a new generation of switch. Due to the common switch is
in the manual and pneumatic basis of development, so I will
introduce common switch.
Company control switch the handan city han mountain high mechanical
and electrical equipment co., LTD. ZKC - 127 k mining company
control switch device to control, the mine pressure fan, pouring
through the signalman or locomotive driver of remote control, make
ZKC - 127 k mining company control switch gear actuator cylinder
push switch automatically closed, this device for flame-proof and
the Ann model, can be used in the prevention of mine, the device is
applicable to coal mine, the coal, mine, bottom and haulage
roadway, switch of centralized control, etc.
2.Mechanical structure parameters
Type: KR - SKQDC
Name: company control pneumatic switch
Overall weight: 490 Kg
The physical size: 3000 x 1030 x 498.6 (LWH) mm
Rail type: I 155 (I140E)
In rail Angle: 16 º
Air pressure: 0.5-0.8 Mpa
ZKC - 12 f mining company control switch remote control transmitter
(this Ann the authentication)
The remote control center oscillation frequency 315 MHZ wireless
transmitting power 10 mw wireless receiving sensitivity - 92 db.
ZKC - 127 k mining company control switch device controller (the
Ann the authentication)
Device controller is mainly composed of Siemens PLC, explosion
protection level 3 regulated secondary constant current power
supply (DC10.3-250 ma) display power supply, remote control
receiver, switch commutator with pneumatic solenoid valve
(specification: manual control one), gas water separator,
controller chassis (flame-proof cavity section provides explosion
protection certificate), constitute. Working voltage: AC127V.
Internal power specification: rated voltage of 10.3 V, working
current acuities 250 ma
Accessories: 8 mm diameter trachea, 5 m cable, etc
ZKC - 12 z mining company control switch gear actuators (this Ann
Executive device switch commutator with cylinder, and the other in
sensor with addition.
ZKC - 12 x mining company control switch device displays (this Ann
Display intuitively show switch at present turnoff state and number
switch, fault information with blank screen instructions, display
panels high brightness LED (green), clearly and accurately display
3.2 products use environment, specification and characteristics
(1) the environment temperature: 0 ℃ ~ + and ℃;
(2) the relative humidity: 96% or less (25 ℃);
(3) or less environmental noise: 75 db;
(4) work pressure: 0.4 ~ 0.6 KPa;
(5) installed in no water spray, water and violent vibration
(6) in a methane explosive mixture, but no damage insulation gas or
steam environment of the mine sites.
(7) working voltage: AC127V, fifty hz;
(8) explosion proof type: mining flame-proof and intrinsically
safe, explosion mark: Exd [ib] I.
(9) explosion this Ann level 3 regulated and two level constant
current power supply (DC24-15-10.3 - DC10.3 V - constant current
(10) downhole remote distance is not less than fifty meters.
(11) product features:
A, with the German imported PLC, completely overcome the SCM system
halted and program run fly phenomenon, enhance the system
B, adopting digital coding technology, system anti-interference
ability is strong, the remote control of the remote control
distance > fifty meters.
C, remote control switch and spare manual control, the switch does
not reach the designated position have warning and reset function.
D, the power supply voltage AC127V. The power supply voltage
fluctuations between 20%. The product can be normal use.
E, gas circuit connection all adopt the quick connector,
installation and maintenance is very convenient.