9 Gauge Hot dipped Galvanized Brick Construction Masonry Wall
Masonry wall reinforced mesh, also called masonry mesh, is used for
concrete constructions to strengthen the structure. It is widely
used in concrete wall reinforcing to prevent or reduce the cracking
of the wall. And our products can increase the strength of your
wall without increasing the thickness. Our masonry wall reinforced
mesh with high tensile strength and good tenacity can be bent
without damaged. T shaped masonry wall reinforced mesh is suitable
for corner construction. In addition, our masonry mesh products
with galvanized surface treatment are not easy to be corroded and
rusted in the concrete constructions. It has long service life.
We provide ladder mesh, truss mesh and T shape masonry mesh mainly.
We also have expanded metal mesh as masonry wall reinforced mesh.
Table 1: Masonry Wall Reinforced Mesh Specifications
|WRMS-1||10' (3.05 m)||2" (50 mm)||Uncoated|
Hot Dipped Galvanized
|WRMS-2||4" (100 mm)|
|WRMS-3||6" (150 mm)|
|WRMS-4||8" (200 mm)|
|WRMS-5||10" (250 mm)|
All ladder mesh products conform to:
ASTM A641 - (Electro galvanized )
ASTM A153 Class B2 - (Hot dipped after fabrication)
ASTM A 82 - (Cold drawn steel wire)
Tensile Strength:80,000 PSI;Yield Point:70,000 PSI minimum;
Reduction of Area:30 %.
ASTM A951-96 - (Masonry wall reinforcing)
ASTM 580 Type 304 - (Stainless steel)
Ladder mesh reinforcement also called Brick Wall Reinforcement Mesh
is welded wire sheet for reinforced masonry construction. It is
used in building surface, wall, ground, bridge, bank and airport.
And its feature is that welding spots of warp wire and weft wire
are on the same surface.
Wire Diameter: 2.5-6.0 mm
Surface Treatment of Ladder Mesh: Can be divided into five types:
Welded after hot dipped galvanized;
Welded after electro galvanized;
Welded before electro galvanized;
Welded before hot dipped galvanized;
Welded by stainless steel wire.
General Technical Information:
Usage: Masonry wall construction.
Materials Available: hot dipped galvanized steel, electro
galvanized steel or stainless steel. Wire diameter: from 2.5mm to
Truss Mesh Structure Width: 5cm, 10cm, 15cm, 20cm.
Structure Length: 3mm.
Wire Spacing: 40cm.
- Packed 500' per bundle (50 pcs - 10' long)
- Corners and Tees packed 25 pcs per bundle
- Greatly reduces cracking that can arise from thermal stresses. This
enhances resistance to water penetration, as cracks are controlled
- Increases lateral flexural strength
- Bonds exterior and interior masonry wythes together in composite or
cavity walls. Also bonds masonry at intersecting walls and corners
- Increases elasticity and performance of masonry walls under various
- Butt-welding of cross rods to longitudinal rods (not more than
16”o.c.). This construction enhances bonding capabilities,
eliminates projection of cross rods beyond the specified width of
reinforcement, and prevents excessive build up of wire in limited
- Continuous deformation along each longitudinal rod for superior
- Fabricated in conformance with ASCE/ACI 530 building code
requirements for masonry structures and ASTM A 951
Various types masonry wall reinforced mesh can be used in the wall,
corner of wall, and any parts to make it become more stable.
Block Ladder Mesh-BLM001
Block Ladder Mesh-BLM002
Block Ladder Mesh-BLM003
Block Ladder Mesh-BLM004
Brick Wall Reinforcement Mesh-BWRM001
Brick Wall Reinforcement Mesh-BWRM002
Brick Wall Reinforcement Mesh-BWRM003
Brick Wall Reinforcement Mesh-BWRM004