FUTU-200 four-head CNC paper tube machine
FUTU-200 four-head CNC paper tube machine Features:
1. For paper tube diameter Ø30-200mm; paper tube thickness of
1-15mm paper tube production.
2. According to different paper tube, tube speed between 0-25 (m /
3. No resistance four machine so that the paper tube strength has
been greatly improved.
4. CNC, light control two fixed-length mode, make the operation
more convenient and faster.
5. The main motor Shanghai strong speed (15kw), this product output
power, and has adjustable speed function.
6. The main engine is WP0155 reducer, this reducer runs smoothly
and the noise is low.
7. By adjusting the foot of the bottom of the console to achieve
the level of stability of the machine.
8. The host two adjustable pedestal arm below each of the three
spherical support column, thereby increasing the stability of the
swing arm, reducing the lower drive bearing single-sided force,
thereby enhancing the service life of parts.
9. The operation of the two mainframe design more humane, the
operator in the paper orientation and the direction of machine
operation can easily control the speed of the machine, this
function in the machine during the production of paper can be
timely deceleration or downtime and reduce waste.
10. The host belt roller diameter of 294mm, instead of the
traditional small diameter belt roller, which greatly increased the
belt roller and belt friction, thus avoiding the belt slip. Discard
phenomenon, thereby increasing the quality of paper tube
production, belt roller The protective cover improves the safe
operation of the production factor, this device is more secure.
11. The host of the mold fixing sleeve adjustable, one for
different diameter mold, the belt can be arbitrarily determine the
location of the mold, to avoid excessive strain on the mold belt;
Second, the use of the mold for a long time caused by wear and
tear, by Adjust the mold fixed sleeve and replace the position, the
mold longer. The head of the six fixed bolts can adjust the
parallelism of the mold, the paper tube production more smooth.
12. The rear of the host body humane design of a toolbox to
facilitate the host operator tools and emergency items stored.
13. Cutting Taiwan walking as a dedicated product, this motor
speed, torque, good stability, synchronization accuracy, which can
improve work efficiency, and to make the paper tube cutting more
14. Cutter's simultaneous cutting and cutting function to avoid the
conventional cutting paper tube paper gap changes and host
instability, to maximize the quality of the paper tube.
15. Cutting table care roller width according to the diameter of
the paper tube can be quickly adjusted by the hand wheel, roller
back and forth by manually turning the hand wheel to complete,
convenient and easy operation.
16. Cutter lift for mechanical and pneumatic type, the speed of the
knife up and down by adjusting the throttle on the cylinder to
control, this adjustment method is extremely simple.
17. Ball Screw Taiwan TBI products, precision screw machining, and
nut with a moderate gap, no noise, smooth operation, long service
18. Inverter for the An Ruitai products, this product is well-known
brands, the practical value is relatively high, low failure rate,
repair rate is small. By frequency control motor to achieve the
machine speed adjustment.
19. PLC control system for the dedicated product, the system
response fast, accurate data processing, good stability,
anti-interference ability, with the professional tracking servo
together constitute a perfect combination.
20. The man-machine interface is a special-purpose product that can
input paper width, paper tube diameter, cutter distance, tube
cutting system and paper tube length through the man-machine
interface. The control system will automatically calculate the
result and realize the speed of tube winding and cutting speed
21. The main electrical relay equipment for the implementation of
Chint products are the middle; cylinder components Austrian days
products. These are well-known brands at home and abroad, with
durable, high practical value characteristics.
22. Cutting table walking lubrication by hand pump unified raise,
easy to operate
23. Into the paper feeding device for the triangular fixed-type
device, replacing the traditional single-column. This device
greatly enhances the stability and smoothness of the feed.
24. The paper shaft is Ф16 hard-wearing hard axis, greatly
improving the service life, paper swelling tight manual mechanical
expansion, easy to operate.
25. The main table on the stainless steel plate, effectively
prevent the bump on its external force and oil, glue on the surface
of its corrosive.
|Paper tube machine model||FUTU-200 four-head CNC paper tube machine|
|Technical parameter||Control system|
|Roll tube paper layer||3-25 layers||PLC controller||Professional products|
|Paper tube diameter||30-200 (mm)||HMI||Professional products|
|Paper tube thickness||1-15 (mm)||Program Version||CX-P 9.04|
|Tube speed||0-25(m / min)||Inverter||An Rui Ji products|
|Fixed-length mode||CNC (light control)||Intermediate relay / contactor||Chint|
|Winding machine head||No resistance four machine head||Signal element (proximity switch, etc.)||bei Funing brand / Shanghai workers|
|Cutting method||Single round knife automatic tracking cutting||Cylinder components||suopai/tian ao brand|
|Core mold fixed way||Flange plus tight||Synchronous control||X axis servo ball screw, Z axis servo screw|
|Glue way||Double-sided adhesive||Synchronous tracking tube cutting system||Orion servo motor|
|control method||Frequency||Cutter lift||Sopian day Austrian aerodynamic|
|Input voltage||380V / 220V||Emergency stop button||Jiangyin Yangtze River brand|
|Number of operators||1-3 people||Configuration device|
|Size (mm)||Drop tube rack||automatic|
|Host Size: L * W * H||2900mm*1700mm*1900mm||Belt adjustment||Manual|
|Land area: length * width||20000mm*9000mm||For glue||Automatic stainless steel heating plastic tank|
|Hub diameter||294mm||Tape for lubrication oil||Automatic lubrication of stainless steel basin|
|Hub height||360mm∕430mm||Tension adjustment||Mechanical adjustment|
|Minimum track||1000mm||Paper holder type||Right-angle fixed lifting on the paper holder|
|The maximum track||1250mm||Roll mandrel||1|
|total weight||5600kg||Roll tube belt||1 article|
|monitor rate||15kw Shanghai strong speed||Bottom, surface paper device||Stainless steel paper holder, paper cone|
|Host speed||1400r / min||Under the rack||Stainless steel plate|
|The maximum wheel speed||62r / min||Host||Stainless steel countertops|
|Hub output torque||8500NM||Paper guide||stainless steel pipe|
|Reducer models||WPO155 Hangzhou Xiaoshan||Host||Stainless steel countertops|
|Linear Guides||Taiwan silver products||Paper guide||stainless steel pipe|
|Ball screw||Taiwan TBI|
|Drive chain model||12A × 2|
|Wheel drive||four-wheel drive|
|Cutter motor||0.4kw gear motor, Shanghai Ott|
|Note: due to the continuous update of the product technology, all
data to the product sample!|
Fixed right-angle lifting on the paper holder
The paper holder is a fixed right-angle paper holder This structure
occupies a small area, replacing the traditional cross-shaped paper
holder, economical and easy to operate more effort. Lifting the
paper for the electric lifting device, the paper faster. Shelf axis
for the solid round bar, can make the paper run more smoothly.
Paper holder of the paper holder, user-friendly design of a hand
holding the paper holder, a hand operation switch, a person easily
complete the lifting process. Tissue paper on the axis of the tray
with high wear-resistant materials and the level of the step
design, both to prevent paper from moving around but also make the
paper roll smooth operation, paper plane at both ends of the plane
design not only guarantees the stability of the paper roll
operation, but also for Paper roll to increase mobility, paper
guide manually adjustability is convenient and fast for the paper
into the mold in advance of the wrong layer, so as to ensure the
smoothness of the paper, the upper and lower guide wheel made of
stainless steel tube height of 1.3 meters for the paper variable
Direction provides sufficient space, the paper is not easy to
Bottom paper holder
The bottom paper holder is a one-time finished structure for
backing paper lubrication and gumming. The end of paper automatic
lubrication system is convenient, clean, easy to operate, uniform
lubrication. Tension control at the end of paper By adjusting the
pressure of the pneumatic valve to control the pressure plate to
control the tension of the end of the paper so that the end of the
paper tension equilibrium.
Under the rack
Sliding tray under the load of stainless steel plate, stainless
steel high wear resistance greatly enhances its service life.
Spray automatic plastic rack
Glue system for the diaphragm pump Pneumatic automatic glue,
pressure can be adjusted by the pressure to change the speed of the
plastic, convenient and easy operation; Glue part of the tray
design more humane, glue more uniform, and for different Level of
paper. Plastic frame for the plastic with a large flow diaphragm
pump, the paper will not appear off the plastic leakage phenomenon.
Scraping plastic rod straight 16 optical axis, not easy to deform.
Hose for high wear-resistant silicone tube, squeegee evenly, use a
long time, manual squeegee scraper can be rotated by scraping the
scraping lever to avoid paper scraps caused by the accumulation of
paper on the plastic scraping rod caused by excessive glue, which
affects The quality of paper tube. Plastic tank for the stainless
steel products, with corrosion resistance, greatly enhance the
service life of the plastic tank. Another water heating layer.
Paper Tube Samples
Q:What can you do if the machine broken?
A:Our machine's warranty period is 12months,if the broken parts
can't repair,we can send the new
parts replace the broken parts freell,but you need pay the express
cost yourself.if after warranty period,we can through
negotiationfor to solve the problems,and we supply the technical
support for the whole life of the equipment.
Q:What about the service after sale?
A: One you have bought our machine, you can call us or email us
telling us the machine problems and any questions about the
machines. We will reply to you with 12hours and help you to slove
Q: How to visit your company?
a.Fly to Beijing airport: By high speed train From Beijing Nan to
Cangzhou Xi (1 hour), then we can pick up you.
b.Fly to Shanghai Airport: By high speed train From Shanghai
Hongqiao to Cangzhou Xi(4.5 hours), then we can pick up you.
Q:You are trade company or factory?
A:We are trade company but we also have own factories. Building
trade company is just for exporting various types of packing
Q. How long the machine could be made?
A:Normally speaking, machine could be made within 45 working days.
If you need machines in a hurry, we can make it for you less than a